South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily)

South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily)

Marsoni

M251S

$716.17

Get it in 3 business days with 1 day shipping. Friday, May 29

South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily)STAGE 3 DAILY Recommended for single mass flywheel (SMF) when original design is DMF. This clutch package is designed for high HP vehicles desiring a start performance similar to O. E. The pressure plate is Race Engineered (SS) and SFI approved with significant load increase over stage 1,2 pressure plates (+600 800 lbs.). Expect a pedal effort increase of 20% 25%. Discs are assembled with heat treated wear resistant hubs; drive plates and springs for

Easy Shipping

Quick Dispatch:

Your South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily) orders ship within 1-2 business days.

Delivery Options:

Standard: 3-7 business days
Fast: 2-3 business days
Express: 1-2 business days

Order Tracking:

You'll receive a tracking link by email once your South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily) ships.

Need Help?
Questions about South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily), sizing, or delivery? We're just an email away.

Live Shipping Estimates:
Enter your location at checkout to see available shipping methods and costs for South Bend Clutch/Flywheel Kit Audi B7 A4 2.0T (Stage 3 Daily) in your area.

Get Shipping Estimates

Country Zip/Postal Code

Exchange/Return Notes

We offer a 30-day return/exchange service after receiving.
Final sale items are not eligible for returns or exchanges.
To process your return/exchange, please contact us at [email protected]
Please click here for more details>>> Return & Exchange Policy

Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.

WAS THIS REVIEW HELPFUL?YesReportShare

Reviewed in the United States on April 16, 2026

Verified Purchase

Nancy filippi

Whiting, US

★★★★★ 5

A must pull your gimbal bearing

You do need to drill a hole but worked perfect

WAS THIS REVIEW HELPFUL?YesReportShare

Reviewed in the United States on December 26, 2025

Verified Purchase

rich911s

Lake Worth, US

★★★★★ 5

Worked for Volvo Penta SX Gimbal Bearing

Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.

WAS THIS REVIEW HELPFUL?YesReportShare

Reviewed in the United States on June 5, 2023